+86 15821372151
Desmodur® N 100
Desmodur® N 100
| CAS No. | 28182-81-2 |
|---|
Introduction & Specs
| Characterization | Aliphatic polyisocyanate (HDI biuret). As the hardener component for lightfast polyurethane coating systems. |
| Specification | |||
| Property | Value | Unit of measurement | Method |
| NCO content | 22.0 ± 0.3 | % | M105-ISO 11909 |
| Viscosity at 23 °C | 10,000 ± 2,000 | mPa·s | M014-ISO 3219/A.3 |
| Color value (Hazen) | ≤ 80 | M017-EN 1557 | |
| Monomeric HDI | ≤ 0.5 | % | M106-ISO 10283 |
| Other data* | |||
| Property | Value | Unit of measurement | Method |
| Viscosity at 25 °C | approx. 8,000 | mPa·s | M014-ISO 3219/A.3 |
| Equivalent weight | approx. 191 | ||
| Density at 20 °C | approx. 1.14 | g/ml | DIN EN ISO 2811 |
| Flash point | approx. 181 | °C | DIN 22 719 |
*These values provide general information and are not part of the product specification.
| Solubility / thinnability | |
| Desmodur® N 100 can be thinned with esters, ketones and aromatic hydrocarbons such as ethyl acetate, butyl acetate, methoxypropyl acetate, acetone, methyl ethyl ketone, methyl isobutyl ketone, cyclohexanone, toluene, xylene, solvent naphtha® 100 and mixtures thereof. Generally speaking, it has good compatibility with the solvents listed. However, the solutions formed must be tested for their storage stability. Only PU grade solvents should be used (max. 0.05 % water, absence of reactive groups such as hydroxyl or amino groups). Aliphatic hydrocarbons are unsuitable as solvents. Desmodur® N 100 should not be thinned to less than 40 % non-volatile content. With time, lower binder content can lead to turbidity and sedimentation. |
|
| Compatibility | |
| Generally speaking, Desmodur® N 100 can be mixed with the followingproducts: aliphatic polyisocyanates such as Desmodur® N 3200, ultra N 3300, N 3400, N 3600 and Desmodur® Z 4470; aromatic polyisocyanates such as Desmodur® L/ultra L, HL and IL/ultra IL; polyester polyols such as Desmophen® 651 and 670; polyacrylates and polyether polyols such as Desmophen® 1380 BT. However, the compatibility of the combinations used should always be tested. |
|
| Properties / Applications | |
| Desmodur® N 100 is used primarily as the hardener component for lightfast two-pack polyurethane coatings with high resistance to chemicals and weathering, very good gloss retention and outstanding mechanical properties. Preferred co-reactants are polyacrylate or polyester polyols. The main applications for systems based on Desmodur® N 100 are as air- and force-drying coatings for automotive and industrial finishing, for wood, furniture and plastics and for corrosion protection. |
| Storage | ||
| – Storage in original sealed Covestro container. – Recommended storage temperature: 5 – 25 °C. – Protect from moisture, heat and foreign material. General information: The product is sensitive to moisture. Storage at higher temperatures will result in increase of color and viscosity. Storage at significant lower temperatures will result in solidification. This solidification is reversible by briefly heating the product without adversely affecting the quality of the product. |
||
| Storage time | ||
| Covestro represents that, for a period of nine months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section “specifications or characteristic data” above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section “storage” above and is otherwise handled appropriately. The lapse of the nine months period does not necessarily mean that the product no longer meets specifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the nine months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the nine months period. |
| Labeling and statutory requirements | |
| This product data sheet is only valid in conjunction with the latest edition of the corresponding Safety Data Sheet. Any updating of safety-relevant information in accordance with statutory requirements – will only be reflected in the Safety Data Sheet, copies of which will be revised and distributed. Information relating to the current classification and labeling, applications and processing methods and further data relevant to safety can be found in the currently valid Safety Data Sheet. |
|
| Further information | |
| The product is used mainly as a hardener in coating materials or adhesives. The handling of coating materials or adhesives containing reactive polyisocyanates and residual monomeric HDI requires appropriate protective measures referred to in the safety data sheet. These products may therefore be used only in industrial or trade applications. They are not suitable for use in homeworker (DIY) applications. |
aton@predawnchem.com
With cooperation with domestic academy of sciences and many institutes, our plant is equipped with ....